广东工业大学学报 ›› 2012, Vol. 29 ›› Issue (3): 96-98.doi: 10.3969/j.issn.1007-7162.2012.03.019

• 综合研究 • 上一篇    下一篇

5083-H321铝合金板材搅拌摩擦焊缝组织演变

刘洪，袁鸽成，黄泽涛，梁春朗，吴亚，吴红辉   

  1. 广东工业大学 材料与能源学院，广东 广州 510006
  • 收稿日期:2011-12-30 出版日期:2012-09-20 发布日期:2012-09-20
  • 作者简介:刘洪（1986-），男，硕士研究生，主要研究方向为先进铝合金材料及加工.
  • 基金资助:

    广东省重大科技专项（2008A090300004）；广东省教育厅211工程学科建设项目

The Microstructural Evolution of Friction Stir Welded 5083H321 Aluminum Alloy Plates

Liu Hong, Yuan Gecheng, Huang Zetao， Liang Chunlang, Wu Ya, Wu Honghui   

  1. Faculty of Materials and Energy, Guangdong University of Technology，Guangzhou 510006，China
  • Received:2011-12-30 Online:2012-09-20 Published:2012-09-20

HTML

PDF (PC)

3098

摘要： 采用搅拌摩擦焊接法焊接了5083H321铝合金板材，借助光学显微镜、扫描电镜、背散射电子衍射分析仪及取向显微成像分析技术对焊缝与母材的组织进行了对比性研究.结果表明，该合金板材的焊缝无宏观缺陷，焊缝成形区呈现出与母材明显不同的组织特征；搅拌摩擦焊使该合金板材中大量的小角度晶界转化为大角度晶界，母材和焊核区的晶粒尺寸分布范围分别为6~55 μm及15~30 μm，晶粒纵横比分布范围分别为2~8和15~3，焊核区呈现均匀化与等轴化的动态再结晶特征.

关键词: 5083铝合金；搅拌摩擦焊；组织；演变；焊缝

Abstract: The 5083H321 aluminum alloy plate was jointed by friction stir welding. The comparative studies of the organization of weld and base metal were conducted with optical microscopy, scanning electron microscopy, electron back scattered diffraction and orientation imaging microscopy. The results show that there are no macroscopic defects in the weld. The organizational characteristics are obviously different between the welding seam and the base metal. Friction stir welding makes a large number of lowangle grain boundaries transform into highangle grain boundaries in the nugget zone. The grain size distribution of the base metal and the nugget zone is 6~55 μm and 15~30 μm respectively while the shape aspect ratio is 2~8 and 15~3 respectively. The grains of the nugget zone show homogeneous and equiaxed morphology characteristics of dynamic recrystallization.

Key words: 5083 aluminum alloy; friction stir welding; microstructures; evolution; weld

［1］ 曹丽杰.铝合金搅拌摩擦焊接技术的研究进展［J］.电子工艺技术,2009,30(2):99103.

［2］ 曾平.搅拌摩擦焊在船用铝合金结构中的应用［J］.船海工程,2010,39(1):5557. 

［3］ McNelley T R.Recrystallization mechanisms during friction stir welding/processing of aluminum alloys［J］.Scripta Materialia,2008,58:349354.

［4］ Mishra R S.Friction stir welding and processing［J］.Materials Science and Engineering,2005,50:7178.

［5］ Arora K S.Microstructure evolution during friction stir welding of aluminum alloy AA2219［J］.Journal of Materials Science & Technology,2010,26:747753.

［6］ 束彪.2195铝锂合金搅拌摩擦焊接头组织及性能［J］.航空材料学报,2010,30(4):1215.
［7］ 王大勇.搅拌摩擦焊接AlLi合金接头的微观组织及力学性能［J］.金属学报,2004,40(14):504508.

［8］ Sutton M A.Microstructural studies of friction stir welds in 2024T3 aluminum［J］.Materials Science and Engineering: A,2002,323:160166.

［9］ 周鹏展.7A52铝合金厚板搅拌摩擦焊［J］.中国有色金属学报,2006,16(6):964969.

［10］ 鄢勇.搅拌摩擦焊工艺参数对5052铝合金接头组织和力学性能的影响［J］.焊接,2009,38(10):5053.

［11］ 沈洋.7075铝合金搅拌摩擦焊研究［J］.特种铸造及有色合金,2007,27(2):145147.
No related articles found!
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 2017 《广东工业大学学报》编辑部
地址：广州市东风东路729号广东工业大学 邮编：510090
电话：020-37626653,020-37626139,020-37626396
邮箱：xbzrb@gdut.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发