广东工业大学学报 ›› 2020, Vol. 37 ›› Issue (03): 63-69.doi: 10.12052/gdutxb.190108

• • 上一篇    下一篇

基于Matlab GUI仿真多光束干涉形成光子晶格

赵泽兴, 石智伟, 左茂武   

  1. 广东工业大学 机电工程学院, 广东 广州 510006
  • 收稿日期:2019-09-02 出版日期:2020-05-12 发布日期:2020-05-12
  • 通信作者: 石智伟(1975-),男,博士,主要研究方向为光场的整形与调控,E-mail:szwstar@gdut.edu.cn E-mail:szwstar@gdut.edu.cn
  • 作者简介:赵泽兴(1997-),男,硕士研究生,主要研究方向为激光器系统
  • 基金资助:
    国家自然科学基金资助项目（11774068）

Simulating Multiple-beam Interference to Form a Photonic Lattice by Matlab GUI

Zhao Ze-xing, Shi Zhi-wei, Zuo Mao-wu   

  1. School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou 51006, China
  • Received:2019-09-02 Online:2020-05-12 Published:2020-05-12

HTML

PDF (PC)

2767

摘要： 提出一种基于Matlab GUI数值模拟多光束干涉形成三维光子晶格结构的方法，通过模拟计算干涉图像光强的分布可以直观地观测光子晶格形状，并探讨了部分参数对光子晶格的影响。在具体的模拟过程中，采用（6+1）束光进行干涉，中心光束为涡旋光，其余6束光环绕中心对称分布。以往通过实验装置研究光子晶格的方法往往误差大，装置调整复杂，实验周期长；而基于Matlab GUI的光子晶格数值模拟方式不仅效率高、误差低、结果直观，而且具有参数调节灵活快速，用户交互友好等优点。

关键词: 光子晶体, 全息干涉法, Matlab GUI, 仿真, 多光束干涉

Abstract: A numerical simulation method of multiple-beam interference to produce three-dimensional photonic lattice structure based on Matlab GUI was proposed. The photonic lattice structures could be observed intuitively by calculating numerically the light intensity distributions of the interference patterns. Moreover, the influence of some parameters on the structures was discussed. In the concrete simulation process, (6+1) beams to interference, where the central beam is a vortex beam, was used, and the remaining six beams distributed symmetrically around the center beam. In the past, the method to study the photonic lattice by experimental device was with serious errors, involving complex device adjustment and long experiment period. Nevertheless, the numerical simulation method based on Matlab GUI in the study has not only high efficiency, low error and intuitive results, but also flexible and fast parameter adjustment, user interface friendliness, and other advantages.

Key words: photonic crystal, Holographic interferometry, Matlab GUI, Simulation, Multiple-beam interference

中图分类号: 

  • TP319
[1] YABLONOVITCH E. Inhibited spontaneous emission in solid-state physics and electronics [J]. Physical Review Letters, 1987, 58(20): 841-844
[2] JOHN S. Strong localization of photons in certain disordered dielectric superlattice [J]. Physical Review Letters, 1987, 58(23): 2486-2489
[3] 陈麟, 杨冰洋, 雍有, 等. 太赫兹金属光子晶体结构研究[J]. 光学仪器, 2018, 40(4): 47-55 CHEN L, YANG B Y, YONG Y, et al. Study of terahertz metallic photonic crystals [J]. Optical Instruments, 2018, 40(4): 47-55
[4] 吴立恒, 王明红. 基于微谐振器的光子晶体滤波器工作特性[J]. 激光与光电子学进展, 2018, 55(2): 254-262 WU L H, WANG M H. Operating characteristics of photonic crystal filters based on micro resonators [J]. Laser & Optoelectronics Progress, 2018, 55(2): 254-262
[5] ZHENG X Z, YANG Y, CHEN S F, et al. Slow photons for solar fuels [J]. Chinese Journal of Catalysis, 2018, 39(3): 379-389
[6] 林斌, 林智鹏. 梯形多缝-六边形阵列复合超宽频带天线[J]. 电子产品世界, 2018, 28(25): 35-37 LIN B, LIN Z P. Trapezoid multi slit-hexagonal array composite ultra wide frequency band antenna [J]. Electronic Engineering & Product World, 2018, 28(25): 35-37
[7] ZHANG H F, LIU S B. Enhanced the tunable omnidirectional photonic band gaps in the two-dimensional plasma photonic crystals [J]. Optical and Quantum Electronics, 2016, 48(11): 508-511
[8] YABLONOVITCH E, LEUNG K M. Photonic band structure: non-spherical atoms in the face-centered-cubic case [J]. Physica B, 1991, 175(1-3): 81-86
[9] SOSHU K, KOKI N, SHOICHIRO K, et al. Ultraviolet laser lithography of titania photonic crystals for terahertz-wave modulation [J]. Materials, 2018, 11(5): 835-849
[10] MASUDA H, YAMADA H, SATOH M, et al. Highly ordered nanochannel-array architecture in anodic alumina [J]. Applied Physics Letters, 1997, 71(19): 2770-2772
[11] KRAUSS T F, VOGELE B, STANLEY C R, et al. Wave guide micro-cavity based on photonic micro-structures [J]. IEEE Photonics Technology Letters, 1997, 9(2): 176-178
[12] WANG X, TONG H, PANG Z, et al. Theoretical realization of three-dimensional nanolattice structure fabrication based on high-order waveguide-mode interference and sample rotation [J]. Optical and Quantum Electronics, 2019, 51(2): 38-45
[13] IVANA L, AGATA L, DUSAN P, et al. 2D periodic structures patterned on 3D surfaces by interference lithography for SERS [J]. Applied Surface Science, 2018, 461(1): 171-174
[14] YOSHIKI N, YOSHIDA M, KAZUHITO O, et al. Fabricating a regular hexagonal lattice structure by interference pattern of six femtosecond laser beams [J]. Applied Surface Science, 2017, 417: 69-72
[15] 吕浩, 尤凯, 兰燕燕, 等. 非对称光束干涉制备二维维纳光子结构研究[J]. 物理学报, 2017, 66(21): 217801 LYU H, YOU K, LAN Y Y, et al. Fabrication of two-dimensional micro-nano photonic structures by symmetry-lost beams interference [J]. Acta Physica Sinica, 2017, 66(21): 217801
[16] 梁文耀, 谭希超, 刘基, 等. 基于激光全息法和泰伯效应的光学晶格制作与精确测量实验教学[J]. 实验室研究与探索, 2019, 38(6): 144-148 LIANG W Y, TAN X C, LIU J, et al. Experimental-teaching about fabrication and accurate measurement of optical lattice based on laser holography and Talbot effect [J]. Research and Exploration in Laboratory, 2019, 38(6): 144-148
[17] LOWELL D, GEORGE D, LUTKENHAUS J, et al. Flexible holographic fabrication of 3D photonic crystal templates with polarization control through a 3d printed reflective optical element [J]. Unt Scholarly Works, 2016, 7(7): 128
[18] GEORGE D, LUTKENHAUS J, LOWELL D, et al. Fabrication of 4, 5, or 6-fold symmetric 3D photonic structures u-sing single beam and single reflective optical element based holographic lithography [J]. Proceedings of SPIE-The International Society for Optical Engineering, 2015, 9350: 93501K-93501K-9
[19] LEIBOVICI M C R. Pattern-integrated interference lithography for two-dimensional and three-dimensional periodic-lattice-based microstructures[D]. Georgia, Atlanta: Georgia Institute of Technology, 2015.
[1] 董振宁, 王俊杰, 罗克文, 陈浪城. 网约车乘客隐私保护的演化博弈研究[J]. 广东工业大学学报, 2023, 40(01): 19-28.
[2] 罗俊伟, 罗向龙, 郑晓生, 陈健勇, 梁颖宗, 杨智, 陈颖. 有机朗肯循环系统换热设备仿真研究[J]. 广东工业大学学报, 2022, 39(04): 128-134.
[3] 吴锡鸿, 叶国华, 黄润业, 张国庆, 杨晓青, 李新喜. 新型管状相变材料热管理系统的数值仿真与实验研究[J]. 广东工业大学学报, 2022, 39(03): 133-138.
[4] 李晋芳, 韦光扬, 何汉武, 蔡嘉鸿, 陈基荣. 一种基于质点弹簧模型的牙龈软组织形变仿真算法[J]. 广东工业大学学报, 2020, 37(03): 49-54.
[5] 王晓锋, 何小琦, 尧彬. PBGA封装回流焊翘曲变形仿真与验证[J]. 广东工业大学学报, 2020, 37(02): 94-101.
[6] 吴丹琦, 赖俊升, 杨俊华, 李学聪, 赖来利, 熊锋俊. 基于局部粒子群算法的家庭用电负荷优化控制策略[J]. 广东工业大学学报, 2019, 36(06): 66-73.
[7] 林贵祥, 刘强, 张浩, 邓加喜, 郭芳名. 一种集成仿真的快速定制设计方法[J]. 广东工业大学学报, 2016, 33(04): 44-50.
[8] 王国林, 沈飞, 周海超, 杨建. 轮胎花纹泵浦噪声分析及低噪声轮胎花纹设计[J]. 广东工业大学学报, 2016, 33(04): 51-55.
[9] 杜军特, 李扬. 参数自整定模糊PID控制方法及其在漆包机中的应用[J]. 广东工业大学学报, 2014, 31(2): 58-63.
[10] 王行, 阳林, 冯勇, 彭仁杰. 基于ADAMS的赛车整车建模与操纵稳定性仿真评价[J]. 广东工业大学学报, 2014, 31(2): 104-108.
[11] 卢志强, 李德源, Luca Diviani. 基于Tsai-Wu失效准则的TSCB人行桥强度分析[J]. 广东工业大学学报, 2014, 31(1): 101-106.
[12] 范劢超，曾岳南. 基于VisSim的直线伺服系统的建模与仿真[J]. 广东工业大学学报, 2013, 30(3): 45-48.
[13] 王行，阳林，彭仁杰，冯勇. 基于ADAMS的FSAE赛车前悬架优化设计[J]. 广东工业大学学报, 2013, 30(3): 105-108.
[14] 李鑫，熊锐，吴坚，陈东兴，熊家秦. 进气歧管的管长和管径对发动机性能影响的探讨[J]. 广东工业大学学报, 2013, 30(1): 97-100.
[15] 汪雪刚，吴多龙，苏华锋，蒋兴勇，李瑞. 同轴腔体带通滤波器的设计与实现[J]. 广东工业大学学报, 2012, 29(4): 54-58.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 2017 《广东工业大学学报》编辑部
地址：广州市东风东路729号广东工业大学 邮编：510090
电话：020-37626653,020-37626139,020-37626396
邮箱：xbzrb@gdut.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发